摘要: IC CD4026是IC其可以及一个执行这两个计数器的功能7段驱动器河 单个IC可以直接在Common Cathode 7段显示器上从零(0)到九(9)计数。只需增加一个高时钟脉冲就可以增加计数。通过级联多个CD4026 IC可以创建一个以上的数字(0-9)。
IC CD4026是IC其可以及一个执行这两个计数器的功能7段驱动器河 单个IC可以直接在Common Cathode 7段显示器上从零(0)到九(9)计数。只需增加一个高时钟脉冲就可以增加计数。通过级联多个CD4026 IC可以创建一个以上的数字(0-9)。
Pin Number | Pin Name | Description |
1 | Clock (CLK) | The counting happens when this clock pulse goes high , this pin is normally connected to 555 timer or other uC to produce a pulse |
2 | Clock Inhibit (INH) | Connected to the Ground (low) of the circuit, to enable clock pin |
3 | Enable Input (DEI) | This pin is connect to +5V (high) to enable the output pins (Out A to Out G) |
4 | Enable Output (DEO) | This is an output which always stays high, this pin will be only if more than one CD4026 IC is used (cascaded) |
5 | Divide by 10 (CO) | This is the carry over output pin; it produces a pulse after counting till 9. This pin will be only if more than one CD4026 IC is used (cascaded) |
6,7,9,10,11,12,13 | Out A,B,C,D,E, F,G | These are the decoded output pins which should connected to 7-Segment display. |
8 | Ground | The ground pin should be connected to ground of circuit |
14 | Not 2 out (UCS) | This is Ungated C segment pin. This is an output pin which will be rarely used when division is required. |
15 | Reset | This input pin when made high (+5V) will reset the count to 0. |
16 | Vcc | This pin powers the IC, typically +5V is used. |
7段显示计数器
可直接驱动共阴极7段显示器
易于与计时器或微米辊对接(TTL兼容)
可以轻松地级联更多IC以显示更大范围的数字
最大时钟频率:6Mhz
提供16引脚PDIP,GDIP,PDSO封装
该IC的工作电压范围为3V至15V,但通常以+ 5V的电压为Vdd / Vcc引脚供电,并且Ground / Vss引脚接地。我们有7个从Out A到Out G的输出引脚,它们直接连接到7段显示器。时钟禁止引脚(引脚2)必须保持低电平(地/ 0V),以便可以将时钟信号发送到IC,同时使能输入引脚(引脚3)也应设为高电平(+ 5V),以便输出引脚(从A到G)可以被激活。
每次将时钟引脚(引脚1)设为高电平时,7段引脚将使计数加一。该时钟源可以从555 IC或与TTL兼容的任何其他数字IC中获得。他们只需产生一个低电压0V和高电压5V的脉冲。在下面的电路中,我使用了1Hz的时钟源来增加计数。因此,数字将每(T = 1 / F)1秒增加一次。
复位引脚(引脚15)用于在高电平时将计数复位为零。其他三个输出引脚(引脚5,4,14)仅在需要级联IC时使用。默认情况下,引脚进位(CO –引脚5)将保持高电平,但是当计数达到“ 9”时,它将发出一个小脉冲,计数将再次从“ 0”继续。这个小脉冲可用于驱动级联IC的时钟引脚以显示多个数字。直接使能输出(DEO)引脚将始终保持高电平,以启用任何级联的IC(如果有)。Ungated C段引脚(引脚14)用于任何除法运算;默认情况下,该引脚将保持高电平;当计数达到“ 2”时,该引脚将变为低电平。
用于7段计数器项目
可用于计算穿过某个点的人或物体
能够显示从0到999的各种数字
用于应避免使用微控制器的项目
社群二维码
关注“华强商城“微信公众号
Copyright 2010-2023 hqbuy.com,Inc.All right reserved. 服务热线:400-830-6691 粤ICP备05106676号 经营许可证:粤B2-20210308